Differences

This shows you the differences between two versions of the page.

--- hardware:printers:3d_printers [2026/06/27 04:46] – scaffold page with current inventory enzi
+++ hardware:printers:3d_printers [2026/08/10 00:00] (current) – Added note for P2S issues with OrcaSlicer Jay
@@ Line 3: / Line 3: @@
 ***
-## Prusa i3 MK3 (@person)
+## Prusa i3 MK3 (@???)
+- owner: @hadn69
+- status: out of service
+- print method: octoprint (octoprint is currently oos)
-- owner: @person
-- status: ???
-- print method: (print method)
 ### Specs
+| spec | stat |
+|:-------------|------------------:|
 | Build Volume | 250 x 210 x 200mm |
 | Max Nozzle Temperature | 300° C  |
-| Max Bed Temperature | 100° C  |
+| Max Bed Temperature    | 100° C  |
-Cool Description
+last checked 7/7/26 needs nozzle/bed calibration, should be otherwise good to go?
@@ Line 24: / Line 27: @@
 - owner: @lily
-- status: in service
+- status: **in service**
-- print method: (print method)
+- print method: Studio PC (BambuSlicer), any PC (~~Orca~~/BambuSlicer)
+- Currently has some issue starting prints directly from OrcaSlicer, default to BambuSlicer at this time.
+### Printing
+- Open BambuSlicer ~~(Or OrcaSlicer)~~
+- Install Network Plugin, if prompted
+- Navigate to 'Device' tab
+- Select 'No Printer +' and select 'P2S-Root'
+- When prompted, enter the Access Code, which can be found via the control panel of the printer on the main settings page.
+- Return to the 'Prepare' tab, ensure all printer settings are correct.
+ - Bed type: Textured PEI
+ - Nozzle: 0.4mm (Hardened Steel)
+ - Flow: Standard
+- Slice and Print!
+### Specs
+| spec | stat |
+|:-------------|------------------:|
+| Build Volume | 256 x 256 x 256mm |
+| Max Nozzle Temperature | 300° C  |
+| Max Bed Temperature    | 110° C  |
+| Active Chamber Heating |  N/A  |
+| Build Plate            | Textured PEI |
+| Nozzle Size (Type)     | 0.4mm (Hardened Steel)|
-Cool Description
 ***
+## Qidi Q1 Pro (@enzi)
+- owner: @enzi
+- status: **in service**
+- print method: USB
+On loan to the space starting 7/5/26 until further notice!
+Todo (as of 7/7/26):
+- lubricate lead screws
+### Printing
+- On any PC, fire up [orcaslicer](https://www.orcaslicer.com)
+- Load up the Q1 pro preset with the **0.6 nozzle** (as of 7/21)
+- Slice, export to an exfat/fat32 formatted drive (it's not picky)
+- Plug in at the top right
+- Pick your print on the display!
+### Notes
+- Filament loader needs to be changed at some point (it's jammed against the rack right now)
+- Have experienced some speghettification (as of 7/21) so the bed might need a wash
+- The rails are very thirsty for lube...
+### Specs
+| spec | stat |
+|:-------------|------------------:|
+| Build Volume | 245 x 245 x 245mm |
+| Max Nozzle Temperature | 370° C  |
+| Max Bed Temperature    | 120° C  |
+| Active Chamber Heating |  60° C  |
+| Build Plate            | Textured PEI |
+| Nozzle Size (Type)     | 0.6mm (Unknown)|
+***
 ## VzBoT-330 (@lily)